1,64 € 2,19 €
ICL8038 Kit generador de señal de función DIY, generador de forma de onda multicanal, práctica de producción electrónica 12-24v 50-200KHZ
Descripción
Product introduction:This product is a function signal generator, belonging to a DIY kit, convenient for welding.Product parameters:Power supply voltage: 12V-24VFrequency: 50HZ-200KHZInstructions for use:Circuit principle:ICL8038 pin function: 1 pin, 12 pin: sine wave waveform adjustment terminal; 2 pin: sine wave output; 3 pin: triangle wave output; 4, 5: frequency and duty cycle adjustment and adjustment; 6 pin: V+, positive power supply ; 7 feet: frequency offset; 8 feet: frequency adjustment input terminal; 9 feet: square wave output terminal. Change the pin to an open collector output terminal. When working, connect a pull-up resistor to the corresponding positive terminal. On the power supply side, if it needs to be compatible with TTL square wave, the pull-up resistor should be connected to the +5V power supply; pin 10: timing capacitor terminal; pin 11: V one, negative power terminal or ground. When using positive and negative power supplies, the output waveform is symmetrical with respect to V; when using a single positive power supply, pin 11 is grounded, and the output waveform is unipolar, with an average voltage of V+/2, pins 13 and 14: empty pins.The frequency range of this kit design is 10 KHz-45OKHz, divided into 5 frequency bands, use switch J2 (short circuit) to cut and adjust, RP1 is frequency adjustment, RP2 is square wave duty cycle adjustment, RP3 is square wave linear adjustment, RP4 It is a sine wave distortion adjustment, RP5 is an output amplitude adjustment, the circuit can be powered by a 12-24V single power supply, input by J1; J4 is a waveform output terminal, of which pin 1 outputs a signal with DC bias, and pin 2 outputs a pure signal. It can be switched by J3 (short circuit).
Con la garantía de:
Opiniones (20)
Opiniones de clientes que compraron este producto
А***ч RU
1/7/2026
¡Todo está excelente! ¡Incluso hay un diagrama esquemático, tanto del circuito como del ensamblaje!
Х***ч RU
1/7/2026
P***H BY
12/25/2025
А***в RU
12/11/2025
А***ч RU
12/4/2025
А***ч RU
11/21/2025
Anónimo BY
11/20/2025
Todas las piezas están en su lugar, todo es tal como se describe. Aún no lo he ensamblado.
Z***h BY
11/1/2025
Todo como siempre. Conjunto completo, todo intacto y a tiempo. Recomiendo al vendedor...
Ч***ч RU
10/7/2025
З***ч RU
9/30/2025
З***ч RU
9/30/2025
m***e BR
9/28/2025
Г***ч RU
8/13/2025
Lo recibí, todo está bien.
V***s BY
8/1/2025
El producto coincide con la descripción, entrega rápida y embalaje seguro. Descripción en chino. El diagrama es claro, las ubicaciones de instalación de las piezas están etiquetadas.
S***H RU
7/31/2025
El producto es bueno, muy satisfecho, llegó antes de lo previsto, el vendedor es correcto.
К***ч RU
7/5/2025
m***e BR
6/12/2025
Т***ч RU
5/12/2025
funciona
Е***ч RU
4/27/2025
P***r PL
4/25/2025
1,64 € 2,19 €
Productos relacionados
- Estuche de transporte para DJI Osmo 360, bolsa de almacenamiento, caja resistente a los arañazos, funda protectora de nailon antiarañazos, accesorios para cámara
- Sistema inteligente de Audio en casa Android 11, amplificador de sonido de teatro en pared, amplificador bluetooth con pantalla táctil, reproductor de música de fondo
- Soporte de montaje para adaptador de conversión 1U a SFX, soporte de alimentación 1U para base GPU compatible con TH3P4G3 Thunderboltc
- Para VIVO X200 Ultra funda dura de PU onda magnética carga inalámbrica funda protectora trasera para VIVO X200 Pro Mini X200S Shell
- 1 Uds memoria de almacenamiento 8G 2666 DDR4 ECC SODIMM RS820RP+ DS1618+ DS3018xs 1RX8 8GB
- 20-500 piezas EL357N-C EL357 EL357N