Convertidor bidireccional del módulo industrial CAN FD RS232/RS485 CAN2.0A/B

The CAN FD TO RS232/RS485 is a DIN-rail CAN FD to RS232/RS485 bidirectional converter, featuring high-speed, low-latency, stable performance, ease of use, and cost-effectiveness. It supports five data conversion modes: transparent conversion, transparent conversion with ID, standard protocol conversion, Modbus protocol conversion, and custom protocol conversion. Enables interconnection between CAN and serial devices, compatible with CAN FD and CAN 2.0A/2.0B protocols.

Features industrial-grade design, supports -40°C ~ 85°C stable working, 9V ~ 36V wide power input, 5Kbps~1Mbps CAN FD arbitration domain baud rate, and 100Kbps~5Mbps CAN FD data domain baud rate.

Supports parameter configuration via host computer, built-in 120Ω terminal resistors (switchable via DIP switches), supports DIN-rail mounting, easy to configure and install.

CLASSIFY

PARAMETER

DESCRIBE

PARAMETER

WORKING VOLTAGE

DC 9V ~ 36V, recommended use 12V 1A

SIZE

110 × 27 × 85.6 (mm)

WAY TO INSTALL

DIN-rail installation

RELOAD BUTTON

Long press to restore factory settings

INDICATOR LIGHT

POWER, WORK, COM and CAN

INTERFACE PARAMETERS

CAN PORT SPECIFICATION

1-ch CAN port, supports CAN FD, compatible with CAN 2.0A/2.0B

CAN PORT BAUD RATE

Arbitration domain baud rate: 5Kbps ~ 1Mbps
Data domain baud rate: 100Kbps ~ 5Mbps

TERMINAL RESISTOR

Built-in 2 × 120Ω terminal resistors,
Switching either DIP switch to ON connects one 120 Ω resistor in parallel.
Switching both to ON connects two 120Ω resistors in parallel

SERIAL PORT SPECIFICATION

Supports 1-ch RS485 or RS232

WORK ENVIRONMENT

WORKING TEMPERATURE

-40℃ ～ 85℃

STORAGE TEMPERATURE

-40℃ ～ 105℃

WORKING HUMIDITY

5% ～ 95% RH (no condensation)

STORAGE HUMIDITY

5% ～ 95% RH (no condensation)

SOFTWARE FUNCTION

MODBUS GATEWAY

CAN FD to Modbus RTU (Master/Slave)

SEND THE MESSAGE

Supports 64 transmission messages

RECEIVE MESSAGES

Supports 64 receiving messages

PROTOCOL CONVERSION

Transparent conversion, transparent conversion with ID, standard protocol conversion, Modbus protocol conversion, and custom protocol conversion

CAN ID

Supports standard frame and extended frame

FRAME ID FILTERING

Supports only standard frames, only remote frames, and custom input frame ID (up to 32 groups)

CHANGE DIRECTION

Supports bidirectional conversion, only serial port to CAN, and only CAN to serial port;

FIRMWARE UPGRADE

Supports the host computer for firmware upgrade

PARAMETER CONFIGURATION

AT instruction and host computer software configuration

PROTECTION PARAMETERS

ESD PROTECTION

Air discharge: 8 KV, Contact discharge: 6 KV

EFT/BURST

Power circuit: 2KV; RS485/RS232 circuit: 1KV; CAN circuit: 1KV

SURGE IMMUNITY TEST

Power circuit: 1KV differential mode, 2KV common mode;
CAN circuit: 2KV common mode

Supports CAN FD To RS232/RS485 Bidirectional Data Communication

CAN FD Arbitration Domain Baud Rate : 5Kbps ~ 1Mbps

CAN FD Data Domain Baud Rate：100Kbps ~ 5Mbps

Industrial-Grade Design

Transparent Conversion, Transparent Conversion With ID, Standard Conversion, Modbus Protocol Conversion, And Custom Frame Headers And Trailers Conversion

[] CAN FD TO RS232/RS485