Acoplador de CC DR-E12 LP-E12 batería falsa + adaptador de cargador PD + Cable cargador USB tipo C para cámara Canon EOS M2 M10 M50 M100 M200

USB Type-C Charger Cable+PD Charger+DR-E12 DC Coupler LP-E12 Dummy Battery For Canon EOS M2 M10 M50 M100 M200 Camera

Model: TC8V-PD + DR-E12

USB-C cable length:120CM
Input:PD 18W-65W
Output:8V

Description:
Product name: QC3.0+PD18W Power Adapter;
Specifications: European regulations (round feet) US regulations (flat feet) British regulations (triangle feet);
Product material: PC fire retardant material;
Input: AC100-240V 50--60Hz; 0.6A
Output:Type-C 5V/3A 9V/2.4A 12V/1.5A
Output:USB-A 5V/3A 9V/2.4A 12V/1.5A
Scope of application: Most smart phones and other digital products on the market
Travel Design:Mini size, convenient to carry, suitable for home, travel, office, etc.

Suitable For:

For Canon EOS M EOS-M

For Canon EOS M2 Canon M2

For Canon EOS M10 Canon M10

For Canon EOS M50 Canon M50

For Canon EOS M100

For Canon EOS M200

And more models.

important!

Please note that with some cameras, closing the camera battery door is a necessary step to use the DC adapter kit. Please refer to our operation manual for the installation example of the dummy battery.

Advantage:

1. High-quality chips,DC-DC converter,high conversion efficiency,Good stability,quiescent current is small,while also serving to effectively suppress harmonic current noise.Using a wide range,suitable for most 7.2V-8.4V and 9V camera.

2. The Camera PD-BX Convertor can't only play the role of power adapter,The convertor integrates 2 chips, one is used to identify PD and QC3.0/4.0 power, The other is used for 9V-24V wide voltage input, After the step-down treatment, the regulated output can effectively prevent high voltage, high current, and prevent short circuit, so it has multiple protection functions.

3. Compared with the ordinary USB Type-A (USB-A) power supply, the USB Type-C (USB-C) input PD power mode will get more power. Don't worry about the power bank will disconnect the power supply when the camera sleeps Output. If you use a Ordinary USB-A power supply,The camera will not be able to shoot at any time, when the camera is in smart sleep mode or standby mode, the Power bank usually disconnects the power output after one minute, which will miss the snapshot.

4. Replace the camera battery handle grip or carry more batteries,camera insert battery grip will too heavy,is not conducive to taking pictures.

5. After connecting to the correct PD and QC3.0/4.0 power adapter or power bank, the red indicator light will always be on when the power is on. Certain models of cameras may consume higher current, so please use a high-performance power supply.

Package includes:

1 x QC USB Type-C Charger

1 x QC USB Type-C Cable

1 x Dummy Battery (DR-E12 )

VERY IMPORTANT: The power of the mobile phone PD charger must be between 18W -65W, The camera can start normally. Only support 18W 30W 45W 60W 65W PD Wall charger / PD mobile power supply / PD Car charger to power the camera, please do not use other devices, otherwise the camera will be damaged. This device is only used to power the camera, Do not connect other devices at the same time, Otherwise, it will cause insufficient power supply.

Tips: General digital battery printed above parameters 7.2V / 7.4V labeled battery, it is the camera's minimum operating voltage, these batteries need to use 8.4V charger, full of power, charger 8.4V said no-load voltage, operating voltage and no-load voltage are two different concepts. External power used in the camera, You need to have enough power to supply, the camera is a load,the operating voltage is far lower than the no-load voltage.Therefore, the Camera adapter's no-load voltage is usually between 8V-9V (Note: the multimeter test is no-load voltage).